MANUAL | QUICK START GUIDE

TRX V2 Racing Simulator

In this Guide

A - SYMBOL LEGEND
B - PART LIST
1. B1 - COMPONENTS
1. B2 - ACCESSORIES
1. B3 - INCLUDED TOOLS
C - ASSEMBLY NOTES
D - ASSEMBLY INSTRUCTIONS
1. TRX V2
E - WARRANTY
F - LEGAL

A - SYMBOL LEGEND

IMPORTANT: Since there are different versions of each product based on your region, please make sure you are using the correct set of instructions. The part number on the following page should match the numbers on your product packaging.

IMPORTANT: Due to the nature of cut aluminum profiles, some metal shavings may remain despite our thorough QA cleaning process. We recommend opening boxes and packaging on a hard surface.

NOTE: Some screws and washers may be pre-installed. These are included in the parts list and will need to be loosened and reattached according to the instructions. Already pre-installed components are color-coded gray, while others are color-coded red, for example:

Color-coded red - supplied in the package separately

Color-coded gray - preinstalled

	Recommended: Two people for the task
	Tighten the hardware
	Keep the hardware loose for adjustments
	Make the necessary adjustments
	Break the tab off the corner bracket
	Safety glasses required
	Attention/Priority needed
	Reserve for the next step
	Mirrored components (same on both sides)

B - PART LIST

B1 - COMPONENTS

Front support module

Top auxiliary module

Lower support module

Front support module

Top auxiliary module

Lower support module

Front bracket module

Monitor stand strut

Wheel tilt left

Wheel tilt right

Adjustment plate

Fixing plate-1

Fixing plate-2

Fixed bracket-1

Pedal module

Seat slider lever

Seat fixed bracket-1

Seat fixed bracket-2

Seat bracket module

Seat slider left

Seat slider right

B2 - ACCESSORIES

Thumb screw

Hex screw

Flange nut

Washer (flat)

Buffer pad

Offset hex key

Button screw

B3 - INCLUDED TOOLS

4 mm hex key

5 mm hex key

6 mm hex key

Wrench

NOTE: Extra hardware mag be included as spare parts.

C - ASSEMBLY NOTES

1 - Left side

2 - Right side

3 - Back side

4 - Front side

INSTALLATION ORDER FOR SCREWS WASHERS

1 - Screw
2 - Lock washer (if applicable)
3 - Washer

HOW TO MEASURE SCREWS

1 - Flat Screw
2 - Hex screw
3 - Button screw

D - ASSEMBLY INSTRUCTIONS

TRX V2

STEP 1

Fit the tabs holes of one side of the lever, then squeeze lever and repreat for opposite side.

NOTE: Some screws and washers come pre-installed and will need to be loosened and reattached according to the instructions.

STEP 2

Pre-tighten the screws, but do not lcok them firmly.

* Please pay attention: the TRX plate side needs to face inward.

STEP 3

STEP 4

STEP 5a

Please note, this support is very tight, with basically no gap. If you find it difficult, ask someone to help lift the upper rod slightly. Then tighten the screws on the top.

STEP 5b

STEP 6

STEP 7a

STEP 7b

STEP 8a

Slightly loosen the two knob screws located at the back of the seat platform.

STEP 8b

* Hold the top plate upright to prevent it from falling.

Turn the T-handle at the rear in either direction until the locking pins unseat from their holes and lift the top plate to the top "G" position.

STEP 8c

Once the locking pins are re-seated into the top holes with a "click" tighten the knob screws to lock the platform in place.

STEP 8d

Remove the seat platform assembly by removing the 4 screws and set everything aside.

STEP 8e

Connect the seat sliders.

STEP 8f

Fit tabs into the holes of one side of the lever then squeeze lever and repeat for opposite side.

STEP 8g

STEP 8h

Reattach the seat platform to the seat slider.

STEP 8i

* Hold here

NOTE: If the locking seat platform locking mechanism is loose, tighten the eyelets on bot sides by holding the center turnbuckle and tightening accordingly.

DO NOT OVERTIGHTEN.

STEP 9a

As shown in the figure, both ends of SBM-01 are simultaneously inserted into the corresponding pipe openings according to the arrow directions.

STEP 9b

STEP 10a

STEP 10b

STEP 11

STEP 12a

* Step 11

STEP 12b

* Step 11

WHEEL BASE MOUNTING - FANATEC PODIUM DD1 / DD2

STEP 13a

STEP 13b

WHEEL BASE MOUNTING - FANATEC CSL DD / GT DD PRO / CLUBSPORT DD / CLUBSPORT DD + / PODIUM DD

STEP 13a

STEP 13b

STEP 13c

STEP 14

* Important: After the entire assembly is completed, first tighten the fixing bolts of the guide rails and side rails, and then tighten the fixing bolts of the brackets in sequence.

STEP 15

Use the offset hex key to tighten or loosen the sliders.

STEP 16a

STEP 16b

STEP 17

E - WARRANTY

The product warranty is provided by CORSAIR MEMORY, Inc. Refer to the terms & conditions of CORSAIR MEMORY, Inc. on trakracer.com