КРАТКОЕ РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ
Podium Steering Wheel Bentley GT3
Quick Start Guide
PACKAGE CONTENT
a - 1x Podium Steering Wheel Bentley GT3
b - 1x Podium Steering Wheel Bentley GT3 Stand / Wall Mount
c - 1x Pikes Peak Grip
d - 1x 5 mm Allen key
e - 1x 2.5 mm Allen key
f - 1x Tweezers
g - 1x USB Type-A to Type-C Cable (~ 300 cm)
h - 1x Sticker Set
FIRMWARE UPDATE
STEP 1
Download and install the latest Fanatec PC Driver.
NOTE: The PC Driver is Windows PC compatible only.
STEP 2
Connect the included USB cable (c) to the steering wheel.
STEP 3
Connect the included USB cable to your PC. The Firmware Update Assistant will then open automatically.
STEP 4
Simply confirm the firmware update and wait for completion. Once complete, you can disconnect your steering wheel.
STEP 5
Connect your wheel base to your PC via USB. Then open the Fanatec PC Driver.
ATTENTION: Use the included USB cable with your Fanatec wheel base.
STEP 6
Ensure that your wheel base is in “PC Mode”.
STEP 7
Simply follow the prompts in the PC driver if a new firmware is available for your wheel base.
NOTE: Read your wheel base manual for more information.
Fanatec.com/manuals
INTRODUCTION
The Podium Steering Wheel Bentley GT3 is the first wheel to feature a high-resolution, self-levelling, round display powered by a dedicated ARM microprocessor. The self-levelling feature is achieved with a gyroscopic sensor while in Exhibition Mode (on the Desk Stand / Wall Mount) and through the steering sensor when attached to a Wheel Base. It is possible to disable the display rotation; see section "Display Rotation".
MODES
Press the button combination as shown to cycle through wheel base modes.
* Wheel base dependent
CENTER CALIBRATION
After a wheel base firmware update "Centre Calibration Required" will be shown in the steering wheel display.
STEP 1
To initiate center calibration at any time, touch the display for about 1 second to open the Tuning Menu.
STEP 2
Turn your wheel to the center position.
STEP 3
Press the button combination as shown.
SHIFTER CALIBRATION
STEP 1
Put your shifter* in H-pattern mode (*shifter sold separately).
STEP 2
Touch the display for about 1 second to open the Tuning Menu and press the button combination as shown.
STEP 3
Gear to be calibrated will be shown in the steering wheel display.
STEP 4
Select the gear.
STEP 5
Confirm gear with the button shown.
STEP 6
Repeat for all gears.
TUNING OPTIONS
STEP 1
Touch any point of the display for approximately 1 second to enter the Tuning Menu.
TUNING MODE
To switch from the Standard Tuning Menu to the Advanced Tuning Menu, touch and hold the center of the display for 3 seconds until the progress ring is 100% green.
STEP 2
Navigate the Tuning Menu using the left FunkySwitch™.
Right or left changes the tuning paramater.
Up / down or rotating the FunkySwitch™ changes the parameter value.
TUNING MENU RESET
To completely reset the Tuning Menu, touch and hold the center of the display to initiate a Tuning Mode switch. Once the progress ring is 100% green, a second progress ring will appear for resetting the Tuning Menu to default values.
STEP 3
Touch the "X" symbol in the lower-right corner of the display to exit the Tuning Menu.
NOTE: The available Tuning options will depend on your Fanatec wheel base and connected peripherals.
PIKES PEAK GRIP
STEP 1
To attach the Pikes Peak Grip, remove the four bolts on the rear of the wheel grips with the included 2.5 mm Allen key and remove the covers.
STEP 2
Remove the four bolts on the Pikes Peak Grip (c) with the included 2.5 mm Allen key and remove the covers.
STEP 3
Align the Pikes Peak Grip with the four holes in the steering wheel frame.
STEP 4
Attach the covers, reinsert the bolts, and tighten them with the included 2.5 mm Allen key.
INTELLIGENT TELEMETRY MODE (ITM) FUNCTIONS
NOTE: The FanaLab software suite is required for ITM activation.
When “ITM” is visible on the display, rotating the top-left rotary switch will enable cycling through various ITM information screens.
BUTTON ILLUMINATION
On Fanatec Wheel Base
STEP 1
Touch any point of the display for approximately 1 second to enter the Tuning Menu.
STEP 2
Navigate to the “Button Illumination” tuning parameter and select “OFF” to deactivate the illumination. Default value is “On”.
STEP 3
Touch the "X" symbol in the lower-right corner of the display to exit the Tuning Menu.
In Exhibition Mode
Press the indicated paddle and button combination simultaneously (shown below) to deactivate the illumination.
DISPLAY ROTATION
STEP 1
Touch any point of the display for approximately 1 second to enter the Tuning Menu.
STEP 2
When attached to a Fanatec wheel base, navigate to the “Display Rotation” tuning parameter.
Select “OFF” to deactivate the display rotation feature. Default value is “On”.
STEP 3
Touch the "X" symbol in the lower-right corner of the display to exit the Tuning Menu.
DESK STAND
STEP 1
To assemble the included Desk Stand, remove the back cover by sliding it off.
STEP 2
Insert the included connector and fasten the two bolts with the included 5 mm Allen key (d).
STEP 3
Attach the stand and fasten the bolt with the included 5 mm Allen key.
STEP 4
Insert the included USB Type-A to Type-C Cable into the back of the connector.
STEP 5
ATTENTION: Place the USB cable in the designated groove before reattaching the back cover to prevent damage.
STEP 6
Slide the Steering Wheel onto the connector and plug the USB cable into a power source (for example USB outlets or USB ports on your PC / game console).
WALL MOUNT
ATTENTION: Take care when securing the Wall Mount to a wall. We recommend this process is performed by a qualified professional; incorrect installation can lead to personal injury or damage.
Screws and / or fittings required for attachment are not included. Choose screws and fittings that are suited to the material in your wall and have sufficient holding strength. If you are uncertain, contact your local specialised retailer.
When choosing the wall intended for attaching the wall mounting bracket, be sure to accurately identify with the help of a qualified professional if there are hazardous objects within the wall cavity that can cause you harm and / or cause damage to the building infrastructure.
Required tools (not included)
Drilling Template
A 1:1 scale template to accurately mark and drill the required holes for the Wall Mount can be found in the Podium Steering Wheel Bentley GT3 PDF Manual (page 18).
ATTENTION: Print size must be set to 100% in your printer settings.
STEP 1
Mark the holes and drill into the wall using a suitable drill bit for your wall type.
STEP 2
Insert suitable dowels in the holes (a hammer may be necessary).
STEP 3
Remove the back cover by sliding it off.
STEP 4
Align the back cover and attach it with four screws using a screwdriver.
STEP 5
Insert the included connector and fasten the two bolts with the included 5 mm Allen key (d).
STEP 6
Insert the included USB Type-A to Type-C Cable into the back of the connector.
STEP 7
ATTENTION: Place the USB cable in the designated groove before sliding onto the wall-mounting bracket to prevent damage.
STEP 8
Slide the Steering Wheel onto the connector and plug the USB cable into a power source (for example USB outlets or USB ports on your PC / game console).
EXHIBITION FEATURES
NOTE: Exhibition Features are only available when connected to a power source through the quick release adapter of the Desk Stand / Wall Mount and not when connected to your wheel base. Appearances may differ depending on firmware version.
TIMEPIECE MODE
The Podium Steering Wheel Bentley GT3 features a classic Bentley styled clock as one of its Exhibition Features. The clock will automatically start-up when the steering wheel is connected to a power source via the quick release adapter of the Desk Stand / Wall Mount.
Clock Adjustment
Minutes
Hold the left shifter paddle in whilst rotating the right thumb encoder to adjust the minutes.
Hours
Hold the right shifter paddle in whilst rotating the left thumb encoder to adjust the hours.
TRACK MODE
Track Map Mode
In this mode, the name of the circuit, telemetry data, and track map with position is displayed, complemented by steering, accelerating, and braking inputs as well as cornering g-force data which neatly encircles the edge of the display.
Full Telemetry Replay Mode
In this mode, the video replay footage is overlaid by a full telemetry data widget which reacts in real-time to steering position inputs and all lateral g-forces are displayed in the top-centre of the widget. Real-time input and cornering g-force data neatly encircles the edge of the display.
Clear Telemetry Replay Mode
In this mode, the video replay footage is overlaid by a minimal telemetry data widget which reacts in real-time to steering position inputs as well as changes in the suspension. Real-time input and cornering g-force data neatly encircles the edge of the display.
NAVIGATION
Timepiece Mode will activate by default when connected to a power source through the quick release adapter of the Desk Stand / Wall Mount.
STEP 1
Tap on the display to activate the Track Mode screens.
STEP 2
Swipe either up or down to cycle between the Track Mode screens.
STEP 3
Swipe either left or right to cycle between a wide range of different tracks.
STEP 4
Tap on the display to reactivate Timepiece Mode.
CLEANING
ATTENTION: Only use a clean, dry lint-free or microfibre cloth without chemicals to clean the display by performing circular motions with minimal force.
BUTTON MAPPING
A = Clutch (Bite Point) Mode (S0)
B = Handbrake + Clutch (S0 + S1)
C = Brake + Throttle (RZ + Y)
D = Mappable Analogue Axes (Left: RX / Right: RY)
* GSB = Game-Specific Button
The product warranty is provided by CORSAIR MEMORY, Inc. Refer to the terms & conditions of CORSAIR MEMORY, Inc. on fanatec.com