MANUAL | QUICK START GUIDE

GT Cockpit Seat

RACING SIMULATOR COCKPIT SEAT

FANATEC ClubSport GT Cockpit Black Seat Front

BEFORE YOU START

Please take a moment to carefully read this guide prior to assembling.

This product is also part of our comprehensive ClubSport GT Cockpit Quick Start Guide.
To learn more, visit: https://www.fanatec.com/p/cockpits/cs_gt_c_blk/clubsport-gt-cockpit-black

CAUTION: Your cockpit is engineered from steel for strength and durability.

  • Some of the components are heavy. Please excersise caution when handling these parts.​

  • Ensure the chosen build area is clutter free and there is sufficient space for assembly. ​

  • Use a soft floor covering such as an old blanket or rug to protect both the finish of your Fanatec ClubSport GT cockpit and your floor during assembly.​​

  • To avoid stripping bolt threads, do not overtighten.​

  • At the end of this guide, you will also find setup tips, suggestions for various driving positions, and peripheral mounting.


INSTALLING THE TWO-PIECE BUCKET SEAT

ASSEMBLING THE OPTIONAL TWO-PIECE BUCKET SEAT

Open the hardware bag labeled SEAT ASSEMBLY.

To complete the step, the following hardware and tools will be used:

CS_GT_C_M8_Allen_Key

M8 Allen Key

CS_GT_C_B7_M8_20mm_Bolts_4x

M8 20mm Bolts (4x)

CS_GT_C_B6_M8_16mm_Bolts_4x

M8 16mm Bolts (4x)

  1. Place the seat on a soft floor covering or blanket, laying it on its left side with the right side facing up.
  2. Insert the top half of the seat into the lower half. Ensure the mounting holes in both seat halves are aligned.
  3. Screw four M8 20mm Bolts (B7) into the left and right sides of the seat as shown in the image below.
  4. Screw four M8 16mm Bolts (B6) into the rear section of the seat as shown in the image below.
NOTE: Only securely tighten the eight bolts once they have all been screwed into the seat.
CS_GT_C_Assembling_Bucket_Seat

INSTALLING THE SEAT BRACKETS

Open the hardware bag labeled SEAT STEP 1A.

To complete the step, the following hardware and tools will be used:

CS_GT_C_S7_M8_25mm_L-Bolts_4x

M8 25mm L-Bolts (4x)

CS_GT_C_W2_M8_Washers_4x

M8 Washers (4x)

CS_GT_C_W3_M8_40mm_Plastic_Washers_4x

M8 40mm Plastic Washers (4x)

  1. Place the seat on a soft floor covering or blanket and lay the seat on its left side.
  2. Place two M8 40mm Plastic Washers (W3) over the pre-drilled threaded holes in the seat side.
  3. Rest the Right Side Seat Bracket (20) on top of the Plastic Washers (W3) and align the vertical slots of the bracket with the holes in the Plastic Washers (W3) and seat.
  4. Insert two M8 25mm L-Bolts (S7) with two M8 Washers (W2) into each pre-threaded hole in the seat side. Do not tighten the L-Bolts on the right side of the seat.
  5. Repeat the process for the opposite side of the seat using the rest of the installation hardware and Left Side Seat Bracket (19).
NOTE: To adjust the amount of recline and seating position height, undo the L-Bolts and move the seat up
or down. Do not tighten the L-Bolts on the right side of the seat yet. See step 1C for when to tighten these L-Bolts.
CS_GT_C_Installing_Seat_Brackets

INSTALLING THE SEAT SLIDE ASSEMBLY

Open the hardware bag labeled SEAT STEP 1B.

To complete the step, the following hardware will be used:

CS_GT_C_P1_R-pins_2x

R-pins (2x)

BLANK
  1. Ensure that the seat rail sliders on the Left and Right Side Rear Frame Assembly (3, 4) are aligned evenly.
  2. Position the seat Slider Adjustment Handle (18) between the pre-installed seat rail sliders.
  3. Secure the handle by inserting the R-pins (P1) through the pre-drilled holes in the left and right seat slider.
NOTE: Some inwards compression of the seat slider handle is required in order to locate it between the seat slider brackets.
CS_GT_C_Installing_Seat_Slider_Assembly

INSTALLING THE OPTIONAL TWO-PIECE BUCKET SEAT

Open the hardware bag labeled SEAT STEP 1C.

To complete the step, the following hardware and tools will be used:

CS_GT_C_M8_Allen_Key

M8 Allen Key

CS_GT_C_B7_M8_20mm_Bolts_4x

M8 20mm Bolts (4x)

CS_GT_C_W5_M8_Spring_Washers_4x

M8 Spring Washers (4x)

CS_GT_C_W2_M8_Washers_4x

M8 Washers (4x)

BLANK
  1. Insert the seat with attached seat side mounting brackets at an angle into the cockpit as shown in the image below.
  2. Make sure that the bracket on the opposite side of the seat has enough play to allow it to be angled slightly downward.
  3. Lower the opposite side of the seat onto the seat slider rail.
  4. Secure the seat to the sliders by screwing in four M8 20mm Bolts (B7), four M8 Washers (W2) and four M8 Spring Washers (W5).
  5. Ensure the L-Bolts on both sides of the seat are positioned in the corresponding slots and tighten the L-Bolts on the right side of the seat.
AFTERMARKET SEATS: Should you wish to mount an aftermarket seat, make sure it has 290mm center-to-center mounting points. There is a limited amount of adjustment for slightly narrower or wider seats.
CS_GT_C_Installing_Bucket_Seat

CARE AND MAINTENANCE

Your Fanatec Clubsport GT cockpit is manufactured to be robust and sturdy during use. However, by following basic care and maintenance steps, you can improve the longevity and performance of your cockpit.

IMPORTANT: This product is designed for adult use. We recommend adult supervision for any children using this product.
  1. Before each use of your cockpit, ensure that all the bolts clamping the pedal assembly in place are secure.
  2. Routinely (at least once every two weeks) check the bolts securing the seat brackets, wheelbase, and pedals to ensure they are secure.
  3. To protect the finish of the cockpit, always sufficiently loosen the cam levers and bolts that secure all adjustable parts when using to prevent scraping or cosmetic damage.
  4. To protect the seat, do not place sharp or heavy items on the upholstered sections.
  5. To clean your cockpit, use a clean, dry microfiber cloth or a vacuum with a soft bristle attachment.
  6. Use caution when adjusting seating position to ensure the seat is positioned in the corresponding slots on either side of the seat, and the tracks are free from debris or fingers when sliding the seat.
  7. To protect your seat, do not place heavy items on the upholstered sections.
  8. Ensure a clutter-free environment before use and check to ensure cables are secure.

WARRANTY

All Fanatec racing cockpits have a 2-year warranty.


LEGAL

©2025 CORSAIR MEMORY, Inc. Trademarks belong to their respective owners. All rights reserved. Fanatec is a brand of CORSAIR MEMORY Inc.