TR160S Racing Simulator Manual | Quick Start Guide | Fanatec

MANUAL | QUICK START GUIDE

TR160S Racing Simulator

In this Guide

  1. A - SYMBOL LEGEND
  2. B - PART LIST
    1. B1 - COMPONENTS
    1. B2 - ACCESSORIES
    1. B3 - INCLUDED TOOLS
  6. C - ASSEMBLY NOTES
  7. D - ASSEMBLY INSTRUCTIONS
    1. TR160S
    1. PEDAL OPTIONS - TR80-PBL2
    1. PEDAL OPTIONS - TR80-PBAL2
    1. PEDAL OPTIONS - TR80-HYPL2
  12. E - WARRANTY
  13. F - LEGAL

A - SYMBOL LEGEND

IMPORTANT: Since there are different versions of each product based on your region, please make sure you are using the correct set of instructions. The part number on the following page should match the numbers on your product packaging.
IMPORTANT:  Due to the nature of cut aluminum profiles, some metal shavings may remain despite our thorough QA cleaning process. We recommend opening boxes and packaging on a hard surface.
NOTE: Some screws and washers may be pre-installed. These are included in the parts list and will need to be loosened and reattached according to the instructions. Already pre-installed components are color-coded gray, while others are color-coded red, for example:

Color-coded red - supplied in the package separately

Color-coded gray - preinstalled

Recommended:
Two people for the task
Tighten the hardware
Keep the hardware loose for adjustments
Make the necessary adjustments
Break the tab off the corner bracket
Safety glasses required
Attention/Priority needed
Reserve for the next step
Mirrored components 
(same on both sides)

B - PART LIST

B1 - COMPONENTS

Aluminum profile

Aluminum profile

Aluminum profile

Aluminum profile

Rear chassis end

Aluminum profile

Aluminum profile

Shifter side plate

Corner bracket

Corner bracket

End cap

End cap

Seat slider right

Seat slider left

Seat slider lever

Front logo plate

Rubber feet

Red profile strip

Cable management clip

40x120 end cap

Aluminum profile

Mounting plate

Outer installation plate

Middle mounting plate

Shifter plate

Shifter support plate

B2 - ACCESSORIES

Hex screw

Hex screw

Hex screw

Hex screw

Screw (flat)

Screw (flat)

Ball bearing nut

Washer (lock)

Washer (flat)

Washer (flat)

Flange nut

Hex screw

B3 - INCLUDED TOOLS

5 mm hex key

6 mm hex key

NOTE: Extra hardware mag be included as spare parts.

C - ASSEMBLY NOTES

1 - Top side

2 - Outside

3 - Back side

4 - Front side

INSTALLATION ORDER FOR SCREWS WASHERS

1 - Screw
2 - Lock washer (if applicable)
3 - Washer

HOW TO MEASURE SCREWS

1 - Flat Screw
2 - Hex screw
3 - Button screw

BC-40 & CB-40

These brackets come with guide tabs on the rear. They help align the brackets to the profile when fitted in the same orientation as the profile. When used in the alternate orientation, these tabs are designed to snap off for a flush mount against the profile.

NS-M8 & NS-M6

Slide T-nuts into the ends of the profiles. Some must be added early, so follow the steps in this manual carefully.

If you miss one, tilt it from the outer edge. Use the Allen key to push it into place, ensuring the hole lines up.

OHK-M8-20

The handle screws are ratcheted to allow for tightening and loosening when space for rotationis is limited. Simply pull the handle out and turn handle into position and push it back in to engage thread.

D - ASSEMBLY INSTRUCTIONS

TR160S

STEP 1

STEP 2

STEP 3

Fit tabs into holes on one side of the lever then squeeze lever and repeat for opposite side.

STEP 4

STEP 5

STEP 6

STEP 7

STEP 8

* Step 7
** Step 6

NOTE: Please pay attention: the TRAK RACER plate side needs to face outward.

STEP 9

STEP 10

STEP 11

Attach parts from step 9 to step 10.

* Please pay attention: There are four NS-M8 nuts placed in this position, reserved for use in step 18.

STEP 12

STEP 13

STEP 14

STEP 15

NOTE: Thread screws just enough to hold "PM" in place so screws do not protrude past "PM" plate.

STEP 16

* Step 12

NOTE: Adjust position after wheel base and seat installation.

STEP 17

NOTE: Adjust position after wheel base and seat installation.

STEP 18

STEP 19

* There are four NS-M8 nuts reserved in step 11.

STEP 20

STEP 21

STEP 22

* Step 20

STEP 23

* Please pay attention: There are two NS-M8 nuts placed in this position, reserved for use in step 24.

STEP 24

* There are two NS-M8 nuts reserved in step 23.

STEP 25

STEP 26

As shown in the figure, tighten the pre-tightening bolts in sequence according to steps 1-24.

STEP 27

Please measure the size with a tape measure, then cut it out with scissors and insert it into the corresponding position.

PEDAL OPTIONS - TR80-PBL2

PART LIST

Pedal plate connector

Pedal plate side mount

Pedal plate

Hex screw

Screw (flat)

Screw (flat)

Flange nut

Lock washer

Washer (flat)

Ball bearing nut

Offset hex key

ASSEMBLY INSTRUCIONS - OPTION 1

STEP 1

STEP 2

STEP 3

STEP 4

NOTE: Rotate to use upper or lower mount.

STEP 5

STEP 6

Adjust the angle of TR80-PP by controlling OHK-MB-25.
Adjust position after pedal and seat installation.

STEP 7

Tighten all the screws.

ASSEMBLY INSTRUCIONS - OPTION 2

STEP 1

STEP 2

STEP 3

STEP 4

NOTE: Rotate to use upper or lower mount.

STEP 5

STEP 6

Adjust the angle of TR80-PP by controlling OHK-MB-25.
Adjust position after pedal and seat installation.

STEP 7

Tighten all the screws.

PEDAL OPTIONS - TR80-PBAL2

PART LIST

Heel plate

Pedal plate side mount

Aluminum profile

Aluminum profile

Hex screw

Screw (flat)

Screw (flat)

Screw (flat)

Ball bearing nut

Ball bearing nut

Offset hex key

Washer (flat)

Washer (flat)

Lock washer

Lock washer

ASSEMBLY INSTRUCTIONS - OPTION 1

STEP 1

STEP 2

STEP 3

STEP 4

* From step 2

STEP 5

NOTE: Rotate to use upper or lower mount.

STEP 6

STEP 7

Adjust the angle of TR80-HP-01 by controlling OHK-M8-25.
Adjust position after pedal and seat installation.

STEP 8

Tighten all screws.

ASSEMBLY INSTRUCTIONS - OPTION 2

STEP 1

STEP 2

STEP 3

STEP 4

* From step 2

STEP 5

NOTE: Rotate to use upper or lower mount.

STEP 6

STEP 7

Adjust the angle of TR80-HP-01 by controlling OHK-M8-25.
Adjust position after pedal and seat installation.

STEP 8

PEDAL OPTIONS - TR80-HYPL2

PART LIST

Pedal plate connector

Pedal plate side mount

Pedal plate

Hybrid heel plate

Hybrid pedal side plate

Hybrid pedal side plate

Flange nut

Hex screw

Hex screw

Screw (flat)

Ball bearing nut

Offset hex key

Washer (flat)

Lock washer

ASSEMBLY INSTRUCTIONS

STEP 1

NOTE: This step can also be chnaged after step 16 from the TRS120S Assembly Instructions.  

STEP 2

STEP 3

Take note of orientation of TR80-HHP-01 Brackets.
They should slope towards the front of the rig.

STEP 4

NOTE:
  • Push footrest as far back as possible to make room for step 5.
  • Keep slightly loose and adjust position after seat installation.

STEP 5

Take note of orientation of TR80-HHP-02 Brackets.
They should slope towards the front of the rig.

NOTE: Keep slightly loose and adjust position after seat installation.

STEP 6

STEP 7

NOTE: Keep slightly loose and adjust position after seat installation.

STEP 8

STEP 9

Tighten all screws.

NOTE: After installing the pedal, you can also proceed with the installation from step 17 of TRS120.

E - WARRANTY

The product warranty is provided by CORSAIR MEMORY, Inc. Refer to the terms & conditions of CORSAIR MEMORY, Inc. on trakracer.com

F - LEGAL

©2026 CORSAIR MEMORY, Inc. Trademarks belong to their respective owners. All rights reserved. Trak Racer is a brand of CORSAIR MEMORY Inc.